|
|
Post by Uncle Hawk on Feb 10, 2008 22:21:58 GMT -5
yes, bodie and tellicoreadyyj, I'm sure you aspire to be just like this fucktard who couldn't get past the first rock you see in front of him, try as he might, he couldn't even touch the hard side, he had to back up and do the easy line just to save his sorry 3 foot lifted ass.  |
|
CSaddict
 
PayPal hater
I love Newbs.
Posts: 3,889
|
Post by CSaddict on Feb 11, 2008 6:37:32 GMT -5
That truck is about 3 minutes away from me. I drive by it almost everyday. Its the local 4 wheel shop that owns it.
|
|
|
|
Post by Buffalo Phil on Feb 11, 2008 11:19:13 GMT -5
That's too bad...
|
|
|
|
Post by HeavyMetal on Feb 11, 2008 11:19:54 GMT -5
that cherokee ruined my life
|
|
|
|
Post by FireFighter32 on Feb 11, 2008 17:27:13 GMT -5
thats a big waggy
|
|
|
|
Post by Buffalo Phil on Feb 11, 2008 19:44:26 GMT -5
Still an XJ.
|
|
|
|
Post by littlelegs13 on Feb 11, 2008 19:45:44 GMT -5
still a sick joke  |
|
|
|
Post by hippie-metal on Feb 13, 2008 20:30:42 GMT -5
i 2 have been contimplatin lowering mine and trimmin it up...now... yes i am mechanically inclinded. but i still gotts sum learning to do...right now i am basically sittin at 8'' high. and either wanna go 6'' or 5''. but if i drop it the 3'' or so will it screw with the long arm setup on it. will i have to get a new set of custom driveshafts? i wanna drop it, but at the same time i dont wanna spend 67564675636546 dollars...mainly cuz i dont have that much but u get the point
|
|
|
|
Post by hippie-metal on Feb 13, 2008 20:32:09 GMT -5
yes, bodie and tellicoreadyyj, I'm sure you aspire to be just like this fucktard who couldn't get past the first rock you see in front of him, try as he might, he couldn't even touch the hard side, he had to back up and do the easy line just to save his sorry 3 foot lifted ass. hahaha prolly cuz he is using 99% of his motor just to start turnin them tires from the stopped postion  |
|
|
|
Post by Uncle Hawk on Feb 13, 2008 22:30:10 GMT -5
Ryan - do you have an SYE? the front shaft should be a stock one, and if you get an SYE you may use a front driveshaft for the rear.
|
|
KtmRacer419
Unibody Connoisseur
straight outta 05
Posts: 7,424
|
Post by KtmRacer419 on Feb 13, 2008 22:47:46 GMT -5
with 8" of lift im willing to bet he has a high angle shaft. takes less droop for the shaft to bind up. mine did when it was at full droop.
longarms should be fine
|
|
|
|
Post by hippie-metal on Feb 14, 2008 17:25:24 GMT -5
with 8" of lift im willing to bet he has a high angle shaft. takes less droop for the shaft to bind up. mine did when it was at full droop. longarms should be fine the drop angle isnt as haggard as u would think. and as 4 the SYE...hawk man...i am abbrevation retarded so.... |
|
|
|
Post by captnkirk89 on Mar 21, 2008 19:45:07 GMT -5
why lower to 5 in.? lower it allllll the way. Low rider XJ :brows:
|
|
|
|
Post by hippie-metal on Mar 21, 2008 20:18:43 GMT -5
why lower to 5 in.? lower it allllll the way. Low rider XJ :brows:  u need to stop talkin to honda owners... u r outta control |
|
|
|
Post by captnkirk89 on Mar 21, 2008 20:56:00 GMT -5
ha im just messin. back on topic, in all honesty, i think takin it down to 5 in. is a good call
|
|
